Homogenizers, pumps, vacuum pumps, shut-off devices, separators, filters, compressors, centrifuges, tanks for food and corrosive mediums. Rambler's Top100

Code

Technical characteristics of the equipment. Technological application.

Price,

USD

2C1

 Vacuum pumps (oilles, slightly noisy).        

Type Power, kW Capacity, m3/h   Speed, l/s
a) NVM-5 0.18 5 1.4 260
b) NVM-10 0.37 10.2 8 330
c) NVM-15 0.55 15 4.2 360

2C2

Rotary reversible milk pump. Type OR-2-A-2.

It is designed for curds, liquid chocolate, jams, liquid dough, mayonnaise, yogurt and other products pumping-over. Controlled capacity – from 0.5 to 3.5 m3/h. Diameter of branch pipes – 25 mm. Speed - 610 revolutions per minute. Power - 0.75kW. Pressure - 0.2 MPa. Weight – 33 kg.

460

2C3

 Flask proportioners.

Pumping-over medium – on order. Material - stainless steel.

from 3600

2BH1

 Pumps for food productions.

Type                                        Capacity, m3/h      Lift of a pump, m

centrifugal PC-100                           2-25                        12-30
centrifugal PC-150                         5-100                        10-45
centrifugal PC-160                         15-80                        10-65
centrifugal PC-170                         0.5-12                     20-100
self – priming PVS-20                       2-20                            15
screw PV-300                                   1-10                      40-60
lamella PL-350                                     18                         5-25

upon receipt of the inquiry

2Z1

 Series of screw pumps for food productions.

Capacity – 0.7-10 m3/h; pressure – 0.5 MPa.

Technical characteristics – upon receipt of the inquiry.

up to 800

2T1

Hetical rotor pumps for high – viscous and nonfluid liquids.

T - -20+80 0 C. Stailness steel. Self-sucking, noiseless, valveless, dead zones are not available, with heating. Explosion-proof electrical motors. Capacity – 4-10 m3/h. Power – 3-4 kW. Suction lift – not less than 6m. Pressure – 0.6-1.3 MPa. Viscosity of medium – up to 10000 cSt. Service life – 6 years.

upon receipt of the inquiry

2T2

Pneumatic membrane pumps for liquids that contains abrasive impurities (up to 1 mm); for viscous, paste-like, corrosive, agitation-sensitive products, such as slips, glaze, petroleum products, margarine, mayonnaise, etc. Pumps can operate in dry working conditions and when pipe - line is locked completely (self-failure does not occur). They can be used for work under water; pumps are explosion-proof , fire-proof. Suction lift – not less than 8 m. Capacity – 2-10 m3/h; 10-25 m3/h; 20-40 m3/h. Pressure – 18-50 m. Maximum temperature – 50 o C. Viscosity of liquids that have heavy fractions (? -up to 4mm) - not more than 10000 cSt. Weight – 45; 70; 120 kg.

upon receipt of the inquiry

2T3

 Ball cocks.

Diameter   – from 10 to 100 mm. Max. temperature – 170 to C. Pressure – 40 kg/cm2. Gaskets (seals):

  1. fluoroplastic – to 20 thousand switches;
  2. of thermo – expanded graphite – 2500 switches.

from 29

to 265

2BJ1

 Tubular centrifuge for oil and juice clarification.

17000 revolutions per minute. Factor of separation – 16940. Power - 3 kW. Capacity – 750 kg/h.

12500

2BJ2

 Tubular centrifuge for clarification of oils and any emulsions that have heavy and light fractions (1.06-1.2).

Capacity-750 kg/h.

12900

2BS1

 Milk pump G2-OPD.

Capacity – 6.5 m3/h.

Technical characteristics – upon receipt of the inquiry.

298

2BS2

 Milk pump G2-OPB.

Capacity - 10 m3/h.

Technical characteristics – upon receipt of the inquiry.

298

2BS3

 Pumps for viscous products VZ-DRA-2.

Capacity - 2 m3/h.

Technical characteristics – upon receipt of the inquiry.

490

2BS4

 Pumps for viscous products VZ-ORA-10.

Capacity – 10 m3 per h.

Technical characteristics – upon receipt of the inquiry.

670

2BS5

 Plug straight through cock.

Stainless steel.  Diameter - 35mm
                        Diameter   - 50 mm

 

68
80

2BS6

 Three-way plug cock.

Stainless steel.

Diameter - 35mm
Diameter - 50 mm

 

 

105
105

2BS7

 Three-way shut-off valve.

Stainless steel.

diameter - 35 mm;
              - 50 mm;
              - 80 mm.

 

 

75
85
125

2BS8

 Disk bolt.

Stailness steel.

diameter  - 35 mm;
               - 50 mm;
               - 80 mm.

 

 

68
90
105

2BS9

 Tanks – stainless steel.

Type E – 1. Cylindrical vertical tanks for substances (capable of flowing in the liquid state).

Working volume (m3)     0.075      0.25       0.5       1.0        2.0         3.0
Price, USD                            380       740      870     1200    1530       2010
Working volume (m3)        4.0         6.0           8.0       10.0      16.0        20.0
Price, USD                          2420      2250         3790      4380     6200       7020

 are indicated in the second column

2BS10

Type E – 3. Cylindrical vertical tanks for substances (capable of flowing in the liquid state). With a jacket for flowing circulation of heat transfer agent. Stailness steel .

Working volume (m3)       0.075         0.25         0.5          1.0         2.0         3.0
Price, USD                              620         1250      1280       1710      2310      3390
Working volume (m3)          4.0            6.0         8.0        10.0       16.0        20.0
Price, USD                            4030         5320      6420       7480    10210     11900

are indicated in the second column

2BS11

Type E – 4. Cylindrical vertical tanks for substances (capable of flowing in the liquid state). Thermo-insulating jacket. Stailness steel.

Working volume (m3)        0.075       0.25        0.5       1.0            2.0         3.0
Price, USD                               670       1285     1510    2050         2550      3430
Working volume (m3)           4.0         6.0         8.0     10.0           16.0       20.0
Price, USD                             4080      5390      5660    7560        10350    12050

are indicated in the second column

2BS12

 Type E – 5. Cylindrical vertical tanks for substances (capable of flowing in the liquid state). Thermo–insulating jacket for heat – transfer agent. Stailness steel.

Working volume (m3)      0.075      0.25        0.5      1.0         2.0           3.0
Price, USD                            900      1500      1740   2340      2880        3760
Working volume (m3)         4.0        6.0         8.0    10.0        16.0         20.0
Price, USD                           4400    5880      6975   8000      10740       12410

 are indicated in the second column

2BS13

Type E - 9. Cylindrical vertical tanks for substances (capable of flowing in the liquid state). Thermo-insulating jacket for flowing circulation. Stailness steel.

Working volume (m3)        0.075       0.25        0.5        1.0          2.0           3.0
Price, USD                               900      1500     1740      2340      2880          3760
Working volume (m3)            4.0         6.0        8.0      10.0        16.0          20.0
Price, USD                              4400      5880     6975      800      10740       12410

 are indicated in the second column

2BS14

 Type E – 10. Cylindrical vertical tanks for fluid substances (capable of flowing in the liquid state). Thermo – insulating jacket for heat – transfer agent (heating electrical elements). Stailness steel.

Working volume (m3)      0.075       0.25       0.5         1.0         2.0           3.0
Price, USD                           1140      2010    2750       3190      4010        5160
Working volume (m3)          4.0          6.0       8.0       10.0        16.0         20.0
Price, USD                            6060      8050      963    11100      14900      17300

 are indicated in the second column

2BS15

 Type – EF - pumping charcoat filters. Tanks for filters. Stailness steel.

Volume – 0.075; 0.25; 2.0 m3.

from 850 to 1575

2BS16

 Agitating (mixing) equipment (for any tanks). Volume – from 0.075 to 20 m3. Technical characteristics – upon receipt the inquiry.

from 430 to 2300

2BC1

 Homogenizer with motor (for emulsions of high quality).

Capacity – 500 l/h. Power – 5 kW. Dimensions – 720? 250? 400. Weight – 60 kg. Food stailness steel.

upon receipt of the inquiry

2BM1

 Installation for emulsion production NGD – 3.0.

Volume – 100 l. Production rate – 3 tn. Technical characteristics – upon receipt of the inquiry

4220

2BM2

 Pumps-homogenizers – power dispenders.

a) NGD – 1.5; capacity –1.5 tn;
b) NGD – 3.0; capacity –3.0 tn;
c) NGD – 5.5; capacity –5.5 tn;
d) NGD – 7.5; capacity –7.5 tn;
e) NGD – 11.0; capacity –11 tn;
f) unloading installation for pump homogenizer (dispenser) YRG-2.
Technical characteristics – upon receipt the inquiry

 

910
1055
1610
1920
2190
450

2BR1

 Frame filter – press FKO.

Filter – presses FKO - 6 (hand – clamping device) and filter – presses FKO – 10, FKO – 20 (hydraulic clamping device) are designed for wine clarification (filtration) including champagne, natural juices, non–alcoholic and other drinks. They allow to obtain wines, juices, syrups and drinks of the highest quality.

-

 

 
a) FKO 6. Capacity – 3000 l/h. Surface of filtration – 6m2. Thickness of filter cardboard - 2.8 – 3 mm. 3800
b) FKO 10. Capacity – 3500 – 5000 l/h. Surface of filtration – 10m2. Thickness of filter cardboard – filter cloth. upon receipt of the inquiry
c) FKO 20. Capacity – 8000 – 9000 l/h. Surface of filtration – 20m2. Thickness of filter cardboard - 2.8 – 3 mm. 26400

2BR2

 Automatic chamber filter – presses KMP.

They are designed for filtering suspensions (content of suspended particles – from 5 to 500 kg/m3) that form sediment with big hydraulic resistance. They are used for starch and treacle and food acids production. Automatic and semi – automatic condition.

Surface of filtration, m2:   2.5;    5;    10;    12.5;     22;      25.

from 4800 to 79000

2BR3

 Vacuum band filters LOK.

They are designed for filtration or corrosive and noncorrosive, quick-falling suspensions (incontinuous solid phase). They are used for production of citric acid as well. Surface of filtration, m2:  1.8;   4;     4.5;    10;   20.

from 9000 to 30000

2BR4

 Set for filtration of prepared beer through a layer of kieselguhr. It allows to obtain beer of the highest quality.

Capacity - 800 dal/h. Volume of frame space – 0.45m3. Surface of filtration - 30 m2. System guarantees reliable operating automatically (automatical condition), exludes losses of product during temporary disconnection.

59000

2BR5

 Aqueous-alcoholic solution filtrating set.

It is used for production of various sorts of vodka. Capacity – 120 dal/h. At customers’ request, the set can be completed with a charcoal column of height 2500 mm (volume – 1.3 m3; capacity – 60 dal/h; weight –380 kg).

19900

2BR6

 Filter – presses FKO.

Filter – presses FKO – 1; 2; 4; 6 (hand–clamping device) and FKO 10; 20; 25 (hydraulic champing device) are designed for wine clarification (filtration) including champagne, natural juices, non–alcoholic and other drinks.

 upon receipt of the inquiry

Model

Capacity:

Surface of filtration, m2:

FKO-1

60

1

FKO-2

120

2

FKO-4

240

4

FKO-6

300

6

FKO-10

450

10

FKO-15

700

15

FKO-20

900

20

FKO-25

1200

25

2AS1

 Separator.

It is designed for gluten thickening in production of corn starch.

Capacity – 12000 l/h.

upon receipt of the inquiry

2AS2

 Separator.

It is designed for extraction of starch from mill starch milk.

Capacity – 15000 l/h.

upon receipt of the inquiry

2AS3

 Separator.

It is designed for corn gluten thickening.

Capacity – 30000 l/h.

upon receipt of the inquiry

2AS4

 Separator.

It is designed for extraction of starch from mill starch milk.

Capacity – 80000 l/h.

upon receipt of the inquiry

2AS5

 Separator.

It is designed for molasses and fodder treacle cleansing (clarification). Capacity – 7300 l/h.

upon receipt of the inquiry

2AS6

 Separator for medical industry.

It is designed for separation of polidisperse and similar emulsions. Capacity – 140 l/h.

upon receipt of the inquiry

2AS7

 Separator for medical industry.

It is designed for thin separation of different medical suspensions. Capacity –100 l/h.

upon receipt of the inquiry

2AS8

 Separator.

It is designed for medical suspension clarification. Capacity - 2500 l/h.

upon receipt of the inquiry

2AS9

 Separator.

It is designed for extraction of suspended albuminous fraction from water extract of beef pepsin. Capacity –500 l/h.

upon receipt of the inquiry

2AS10

 Separator for microbiology industry.

It is designed for clarification of cultural liquids. Capacity – 2000 l/h.

upon receipt of the inquiry

2AS11

 Separator for microbiology industry.

It is designed for concentration of products.

Capacity – 2500 l/h.

upon receipt of the inquiry

2AS12

 Separator.

It is designed for separation of free fat acids from glycerine water.

Capacity – 2500 l/h.

upon receipt of the inquiry

2BW1

 Medical steam sterilizer GK-100.

It is designed for sterilization with steam that is under pressure. Vacuum drier. Automatic control of sterilization regimes.

Number of sterilization regimes – 3.

Usefull volume of sterilization chamber – 100 l.

Rated power consumptions – 12 kW.

4200

2BW2

 Homogenizers.

They are designed for homogenization of milk, milk products, fruit, juices, creams, lubricants, lacquers, i.e. emulsions and dispersions of all sorts.

A single – stage head , a two-stage head.

upon receipt of the inquiry
Type Capacity, dm3 per h. Installed power of an engine, kW
K5-OG2A-1.25

1250

11
A1-OG2M-2.5

2500

18.5
A1-OG2M

5000

37
K5-OG2A-250

250

4
K5-OG2A-500

500

5.5

2BW3

 Screw compressor (blowers).

Compressed air has cleanliness (oil content – less than 3 mg/m3) of a high quality. Air compressor – up to Pmax. = 1000 mb or vacuum – up to Pmax. = 500 mb. Capacity – from 30 m3/ h (0.5 m3/min) to 21000 m / h (350 m3 / min). Power – from 1.5 to 500 kW.

A field of application :

  1. aeration of chambers with active slime;
  2. water preparative equipment;
  3. pneumatic transport (for flour, cement, lime);
  4. pneumatic transport (an intake of ash from furnaces);
  5. air blowing to metallurgical furnaces;
  6. air blowing to furnaces for lime roasting;
  7. mills and bakeries;
  8. breweries;
  9. granaries.

upon receipt of the inquiry

2BW4

 Mini vibrodrier A1–LSV (with electric or steam air heater).

It is designed for meat-bone broth, casein, granular products (seeds, cereals, grain, cut vegetables, medical preparations and chemical substance drying. It settles problems of a wasteless technology .

Capacity (dried product):

a) liquid product (egg melange) drying - 3-3.5 kg per h;

b) casein, seeds, cereal drying (a drying cycle - 25± 5 min) – 1.5-3

kg per cycle;

c) cut vegetable-and-fruit drying (a drying cycle – 1-2 h) – 1-2 kg

per cycle.

from 10200 to 11280
2BW5 Plants for liquid product drying in vibro-boiling layer of inert

material.

High intensity of heat-exchange processes.

Field of application: egg mass (melange), white of egg, yolk of egg, meat-bone broth, brewer’s yeast, animal blood, seaweeds, medical preparation, polymer drying (for example: GIVPAN that is used for a boring solution thickening in oil production).

Plants with capacity up to 300 kg per h (evaporated moisture) can be manufactured on order.

Technical characteristics here.

are indicated here.

2BJ35

 Continuous sediment scroll-discharge centrifuges

OGSH and FGSH types horizontal, sediment scroll discharge centrifuges are designed for continuous separation of liquid non-uniform suspensions, containing a solid phase, the density of which is higher than of liquid one.
Thanks to design simplicity, process continuity, minimum maintenance, OGSH centrifuges are widely used in various production process of chemical, pharmaceutical, meat and milk, fish processing and other branches of industry. Last years heavy-duty centrifuges become widely spread for dewatering of drainage municipal and industrial water sediments.

Specifications here.

upon receipt of the inquiry
2BJ7 Compressors for liquefied gas production

Designed for compression of air and nitrogen in air separating units for various liquid gases production.
The compressors 6VM16-150/200 and 6GM16-150/200 make up units for liquid oxygen production of capacity 2300kg/h as well as units for liquid and gaseous nitrogen and argon production.
The compressor 6GM16-145/200M is designed for hydrogen (nitrogen) compression at plants of aerospace industry.
The company manufactures air separating units on the basis of compressors 4VM10-55/71, 4GM10-55/71 and 4GM2.5-30/9S for production of liquid oxygen (of capacity 300kg/h ), argon (of capacity 40 kg/h ) and other gases.
The compressors 2GM2.5-5/1.7-71S and 2GM2.5-4/1.1-71S are designed for completing units for production of carbonic acid for food and other branches of industry. In this case the first compressor is used for units of carbon dioxide production, which is extracted at combustion products utilization, the second one - for carbon dioxide production from fermentation products.
Compressors 4GM10-55/71S and 4GM2.5-1.6/78-161S are designed for use at nitrogen-oxygen stations.
Compressors for liquefied gases production have automatic control, check and protection system ensuring remote control and check.

Specifications here.

A list of the components - upon receipt of the inquiry.

 are indicated here.
2BJ8 VK-type liquid-packed ring compressors

The compressors are designed for compression or transportation of air or inert gases insoluble in water as well as aggressive gases not producing corroding effect on the compressor flowing part materials. The compressors can be used for transportation of dust-laden gases with content of solid particles of no more than 0.1mm size and little water content for food, chemical, metallurgical and other branches of industry.
The compressors can be equipped with any electric motor of power and rotational speed corresponding to documentation requirements.

Design features:

Rotary, horizontal, liquid-packed ring, single-stage, with axial suction and discharge.
They are of a simple design. The rubbing parts in the working space are not available. The antifriction bearings serve as supports. The shaft sealing is soft gland packing.
The flowing part for compressors VK-50M1, VK-100/1.0 and VK-150/1.2 is made of cast iron and carbon steels, for compressors VK-50N and VK-150/1.2N - of corrosion-proof steels, for VK-50T - of titanium alloy.

Specifications here.

 are indicated here.
2BJ9 Air compressors of general industrial purpose and special purpose.

Designed for atmospheric air compression and used in various branches of industry.
Compressors design is piston, horizontal, two-stage with synchronous motor as a drive.
Driving mechanism lubrication is circulating pressurized from a built-in gear type pump. Cylinders lubrication is from a plunger pump.
Compressor cooling is of water type, closed with pressure discharge.
Compressors are equipped with automation ensuring control, protection and switching off at emergency conditions of the most important parameters.
Specifications here.

A list of the components - upon receipt of the inquiry.

 upon receipt of the inquiry
2BJ10 Unified mobile compressor unit UKS-400V-P4M
Designed for filling in field conditions tanks and other vessels by compressed to high pressure dry and clean air.
The station is completely autonomous, adopted for transporting by different kinds of transport and can be operated at any climatic conditions.
High purifying degree of compressed air produced by the station allows to use it in systems, designed for breathing.
 

Station specifications here.

 upon receipt of the inquiry
2BJ22 Vortex pumps

Designed for pumping water, neutral, chemically active fluids, viscosity up to 36 cSt, temperature up to 85 °C, with a content of solid particles up to 0,01% by mass, size up to 0,05 mm.

Technical characteristics here.

 upon receipt of the inquiry
2BJ23 VVN-type liquid-packed ring vacuum pumps

The pumps are designed for suction of air or inert gases insoluble in water as well as aggressive gases not producing corroding effect on the pump flowing part materials.
The inlet gas pressure is up to 0,01 MPa, the outlet one is atmospheric. They can be used for suction of dust-laden gases with content of solid particles of no more than 0,1 mm size and little water content.
The flowing part for pumps VVN2-50M, VVN2-150M and VVN2-300 is made of grey cast iron and carbon steels, for pumps VVN1-12TM and VVN1-50TM - of titanium alloys, for VVN2-50N and VVN2-50H - of corrosion-proof steels.

Technical characteristics here.

 upon receipt of the inquiry
2BJ24 Finned-and-rotary vacuum pumps

Designed for pumping-out air and non-aggressive gases (vacuum-pumping) beforehand cleaned from moisture and mechanical impurities.

Technical characteristics here.

 upon receipt of the inquiry
2BJ25 Overhanging pumps for sewage.

CN-type units are designed for water supply systems, pumping polluted drainage and faecal water with density to 1050 kg/m3 , the hydrogen index pH from 5 to 10, temperature from 5 to 80 deg.C, solid impurities of volume concentration to 5%.
CN-type pumps with capacity from 100 to 1100 m3 are of a centrifugal type, horizontal, single-stage, single-casing, overhanging.

Technical characteristics here.

 upon receipt of the inquiry
2BJ26 Overhanging mud pump

CPN-type units are designed for pumping high abrasive hydraulic mixtures with density to 1300 kg/m3, with the hydrogen index pH from 6 to 12, with temperature from 5 to 80 deg.C with solid impurities of volume concentration to 30%.
CPN-type centrifuges are centrifugal, horizontal (at customer's request they can be of vertical make), single-stage, single-casing,overhanging.

At customer's request the pump can be equipped with a hydraulic valve of a gland seal.

Specifications here.

 upon receipt of the inquiry
2BJ27 Axial chemical pumps

Designed for pumping chemically active fluids in vaporizers and units with temperature up to   140 °N,   density up to 1800 rg/m3, containing solid particles up to 20% by mass, size up to 0,5 mm.

Technical characteristics here.

 upon receipt of the inquiry
2BJ28 Oil gear pumps

Designed for pumping of oil products (oils, mazut, diesel fuel, petroleum) and operate in lubrication system.

Technical characteristics here.

 upon receipt of the inquiry
2BJ29 Three-screw pumps

Designed for pumping fluids possessing lubrication properties, without abrasive additives, viscosity 28-740 cSt, temperature up to 80°C.

upon receipt of the inquiry
 Pump 
 type 		  Capacity, 
m3 /h		  Pressure, 
MPa		  Rotational speed 
(synch.),rpm		  Consumed 
 power, kW 		  Overall dimensions 
mm		  Pump weight, 
kg
3V 8/100 12 100 3000 45 750 x 275 x 270 67,5
3V 16/25 22 25 3000 20,5 555 x 190 x 305 88
Note:  * - on the basis of the pumps, indicated in the list, development and fabrication of new modifications with different performances is possible.
2BJ31 "H"(NK) - type centrifugal overhanging pumps

The pumps are designed for pumping chemically active and neutral media with hydrogen index pH=4...9 and temperature up to 165 deg.C. The pumps with the flowing part,made of titanium, are designed for pumping liquids with hydrogen index pH=2. They are used in chemical, food, oil-refining industries.

Technical characteristics here.

 upon receipt of the inquiry
2BJ32 CNS-type and NSSH-type centrifugal pumps

The pumps are designed for pumping chemically active and neutral media with the hydrogen index pH=6.5...8.5 and temperature to 80 deg.C.
They are used at water discharge units for coal mines, in oil-extracting and oil processing industry, for feed water supply and so on.

Technical characteristics here.

 upon receipt of the inquiry
2BJ33 Continuous filtering centrifuges with reciprocating-pusher discharge of sediment.

FGP type filtering centrifuges are horizontal machines with reciprocating-pusher discharge of sediment, designed for mechanical separation of suspensions with large and medium crystal solid phase, rapidly losing their yield strength with solid phase content more than 50%.
        Owing to compactness, simplicity of maintenance, production process continuity, possibility of sediment washing, high productivity, these types centrifuges found wide usage in chemical, metallurgical, ore mining, sugar and other branches of industry.

Technical characteristics here.

 upon receipt of the inquiry
2BJ34 Tubular   centrifuges

Vertical high-speed centrifuges with a tubular bowl of OTR-102K-01 and RTR-102K-01 type are specimens of a wide variety of centrifuges, manufactured by the company.
OTR-102K-01 type centrifuge with a clarifying bowl is designed for fine clarifying of suspensions with a fine dispersion solid phase, the content of which does not exceed 2% and solid and liquid phases ratio not less than 1,1.
These centrifuges are batch. As the sediment accumulates on bowl walls, the centrifuge is shut down and the bowl is subjected to cleaning.
RTR-102K-01 type centrifuge is a machine with a separating bowl and designed for continuous (if no solid phase) separation of emulsions with density ratio of heavy and light phases in the range of 1.06 ... 1.20.
In case of separation of emulsions, containing solid particles, the centrifuge RTR-102K-01 is required to be periodically shut down for bowl cleaning.
Owing to compactness, high separating ability, usage of corrosion-resistant materials for assemblies and parts, contacting with a handled product, modern design, centrifuges OTR-102K-01 and RTR-102K-01 are extensively used specially in the pharmaceutical industry for complex fractionating of blood plasma albumins, in vaccines and serums production, in microbiology, for oils purification and others.

Technical characteristics here.

 upon receipt of the inquiry
2BJ36 Continuous filtering centrifuges with reciprocating-pusher discharge of sediment

FGP type filtering centrifuges are horizontal machines with reciprocating-pusher discharge of sediment,designed for mechanical separation of suspensions with large and medium crystal solid phase, rapidly losing their yield strength with solid phase content more than 50%.
Owing to compactness, simplicity of maintenance, production process continuity, possibility of sediment washing, high productivity, these types centrifuges found wide usage in chemical, metallurgical, ore mining, sugar and other branches of industry.

Technical characteristics here.

upon receipt of the inquiry
2BJ37 Filtering settling centrifuges with sediment knife discharge

FGN type automatic filtering centrifuges are horizontal batch sediment knife-discharge machines, designed for separation of suspensions with a medium and fine grained (particles size more than 30΅m) soluble solid phase at its volume concentration more than 10%.
This type centrifuges provide high quality of a solid phase washing. Due to this fact they are widely used, when producing sodium sulphate, anthracene, iron and nickel vitriol, boric acid, soda, sodium chloride, starch and in other production processes of the chemical industry and contiguous to its branches.
OGN type automatic settling centrifuges are batch horizontal sediment knife-discharge machines, primarily designed for separation of hardly filtering suspensions with an unsoluble solid phase (particles size more than 5΅m). Sediment washing is not specified in these centrifuges.

Technical characteristics here.

upon receipt of the inquiry
2BJ3

Ball cocks DN 40 – DN 100.

They are used as shut-off facilities in pipe-lines transporting nonaggressive natural gas, air, oil. They are also used when erecting compressor stations, gas transferring units and other technological equipment.

Nominal diameter, DN – from 40 to 100 mm.

Nominal pressure, PN – 16 kg/cm2.

Temperature of working medium – from –60 to +80oC.

Material of the cock body – low-alloyed steel.

Sealing material – wear-resistant polymer.

Type of drive: RP – hand drive;

PP – pneumatic drive.

upon receipt of the inquiry

2BJ4

 Ball cocks.

They are designed for installation in pipe-lines transporting nonaggressive natural gas, air, oil.

Nominal diameter DN, mm                       Nominal pressure PN, kg/cm2

                        6                                                                 160
                      15                                                                   80
                      25                                                                   25
                      32                                                                   25
                      40                                                                 100

Temperature of working medium – from –60 to +80oC.

Material of a body – steel.

Sealing material – wear-resistant polymer.

Method of attachment – a ball-cone one.

Hand drive.

upon receipt of the inquiry

2BJ5

 Globe valves.

They are designed for installation as globe (shut-off ) facilities in pipe-lines transporting petroleum products, nonaggressive natural gas, air, oil.

Material of the body – stainless, carbon steel.

Type of drive: electric, hand.

 upon receipt of the inquiry
Nominal diameter DN, mm Nominal pressure PN, kg/cm2 Temperature of working medium, o C Type of drive

25

25

- 60   + 400
- 40  + 150

 hand
hand

32

25

- 40   + 150

 hand

40

 160

- 80   + 200

 hand

50

16

- 40   + 150

 electric, hand

50

25

- 60   + 400

 electric, hand

50

40

- 40   + 150
- 60  + 400

 electric, hand
hand

80

16

- 40   + 400
- 40  + 150

 hand
electric

2BJ6

 Gate.

It is designed for air, gas, oil, water transporting pipe-lines.

 upon receipt of the inquiry
 

Nominal diameter DN, mm

  

Nominal pressure PN, kg/cm2

 Temperature of working medium, o C Type of drive

100

100

16

25

 up to + 400

up to + 500

 hand, electric

hand, electric

2BJ13

Vacuum drum filter B-YA-N-180.

It is designed for filtration of suspension of sodium bicarbonate in soda ash production and in other productions as well. Base material – stainless steel. Filter capacity (moisture content in sediment – 16-17 %) – 180-200 tn per 24 h. Moisture content in raw sodium bicarbonate – 16-17 %. Power consumption – not more than 10 kW. Weight of a filter – not more than 9250 kg.

upon receipt of the inquiry

2BJ14

Vacuum drum filter BB-5.4.

It is designed for filtration of suspension of sodium bicarbonate in soda production. This filter has not cells and distributive device. This fact simplifies its design and allows to collect filtrate and flu-shing fluid separately. Base material – stainless steel. A complete set includes electrical equipment. Filter capacity (output of finished products) – 450 tn per 24 h. Moisture content in sediment after filtering – 14-16 %. Compressed air demand – 800-1000 m3/h. Power consumption – not more than 5.5 kW.

upon receipt of the inquiry

2BJ15

Vacuum drum filter BBM45-3.14-1G.

It is designed for filtration of difficult-filtering suspensions in tita-nium dioxide production and in other productions as well. Base material – stainless steel or titanium. Filter capacity (suspension) - not less than 4000 kg per h. Power consumption – not more than 11.5 kW. Weight of a filter – not more than 22900 kg.

 

upon receipt of the inquiry

2BJ16

Centrifugal spraying machine (atomizer).

It is designed for thin atomization of materials (solutions, emulsions, suspensions) capable of flowing in the liquid state in drying chambers of spray driers (upper and lower feed of heat-transfer medium with to – up to 830 oK (600 oC)). Disk rotational speed – 8000 or 10000 revolutions per min.

Technical characteristics here.

upon receipt of the inquiry

2BJ10

Complete production line.

It is designed for weak nitric acid production. It is used in production of nitric acid from liquid ammonia and air. Production rate – 360000 tn per year. Acid concentration – 60 %. The content (by volume) of nitric oxides in exhaust gas – 0.004 – 0.006 %.

Technical characteristics here.

upon receipt of tthe inquiry

2BJ18

 Column apparatuses for mass-exchange processes.

There is a high dividing capacity under great steam-and-liquid pressure. Small losses of pressure. Easiness of mounting and dismounting.

Technical characteristics here.

upon receipt of tthe inquiry

2BJ20

 Apparatuses-reservoirs.

They are used for receipt, storage, processing and distribution of products in chemical, oil-chemical, food and other industries (working pressure – up to 25 MPa (250 kgs/cm2); temperature – from -210oC to + 700oC; volume – up to 1000 m3).

Apparatuses-reservoirs without internal arrangement.

Apparatuses-reservoirs with mixing equipment.

Special apparatuses-reservoirs (including functional purpose):

absorbers; extractors; stills;

desorbers; catalytic reactors; oxidizers;

washers; combustion chambers; reactors;

regenerators; mixers; separators;

neutralizers (for finish chlorinators.

neutralization);

Apparatus are developed on the individual design; they can be manufactured of carbon and corrosion-resistant steel, titanium alloys on the base of nickel (nickel – molybdenum alloy – C).

 upon receipt of the inquiry

2BJ21

Heat-exchange apparatuses.

It is designed for water, neutral and chamically active liquid pumping (viscosity – up to 36 cST; to – up to 85oC; content of hard inclusions (by mass) – up to 0.01 %; dimensions – up to 0.05 mm).

upon receipt of the inquiry

Go to the list.

 

Rambler's Top100